← Back to blog

Brick Facade Inspection: What to Check and When to Act

November 10, 2026
Brick Facade Inspection: What to Check and When to Act

A brick facade inspection is a planned, documented walk around every wall of a building. You look for cracks, spalled bricks, failing mortar joints, rusting steel and signs of moisture, and you record what you find. For most Richmond, VA homes and small commercial buildings, a careful look from the ground twice a year, plus a check after any major storm, catches problems while they are still small repairs.

This guide explains what to look for and how to record it. It also covers what the findings mean for older Richmond brick, where lime mortar is the right material for repairs.

Heritage Masonry & Brick
Address Brick Facade Damage Early
Heritage Masonry & Brick repairs crumbling mortar, cracked walls and water-damaged brick using traditional methods and matched materials.
Explore brick repair services

TL;DR

  • Inspect from the roofline down to the foundation, one wall at a time, and photograph everything you record.
  • Watch for stepped or diagonal cracks, crumbling or sandy mortar, spalled bricks, rust at lintels and damp or stained walls.
  • Check at least once a year, ideally in each season, and after every severe storm.
  • Structural signs need a professional evaluation. Mortar and brick repairs on historic Richmond buildings should use lime-based mortar matched to the original.
  • Routine maintenance in a Richmond historic district does not need a Certificate of Appropriateness, but changes in appearance may.

Table of Contents

What a brick facade inspection covers

The Brick Industry Association describes maintenance as three parts: periodic inspections to document the building's condition, regularly scheduled maintenance tasks, and specific repairs for problems the inspection finds. The inspection is the part that tells you what the other two need to be.

A full inspection looks at the exterior and the interior. On the outside, you survey each elevation, using binoculars to see upper floors up close. On the inside, you look for stains or damaged finishes below windows, along exterior walls and near the ceiling line, because these often point to water getting in through the brick.

The National Park Service adds a list of conditions to check on exposed masonry: cracking, spalling, bowing, sweeping, leaning and mortar deterioration. Bowing is a vertical bulge. Sweeping is a horizontal one.

How to walk the building

A consistent routine matters more than special equipment. The NPS guidance for historic buildings says exterior inspections usually go from the roof down to the foundation, one elevation at a time, always moving around the building in the same direction. It also recommends inspecting all building features after any significant weather event.

  1. Start with the roofline. Look at the parapet, chimney, gutters and downspouts. Overflowing or leaking gutters are a common reason brick below stays wet.
  2. Work down each wall. Note cracks, loose or missing bricks, crumbling joints and any stains. Use binoculars on upper stories instead of climbing.
  3. Check openings. Look at the brick above windows and doors, at arches, and at the sills. Rust stains or sagging above an opening deserve attention.
  4. Finish at the foundation. Look at the base of the wall, steps, planters, and where soil or paving meets the brick. Check crawl space piers from the inside if you can reach them safely.
  5. Record it. Photograph each wall, then make a simple annotated sketch. Academic guidance on facade inspection notes that annotated sketches are especially useful for tracking changes in cracks, lost mortar and loose units, and should be supported by high-resolution photographs. Put a coin or ruler next to a crack so you can compare it next season.

Keep your feet on the ground. The NPS guide also asks that inspections be done with safety in mind and notes that older buildings can carry lead-based paint, asbestos and bird droppings. Do not lean a ladder against old brick or step onto a roof you have not checked.

Signs of damage and what they usually mean

What you seeWhat it can meanNext step
Mortar that is sandy, recessed or falling outJoints have worn away and water can enter the wallPhotograph, then have the joints assessed for repointing
Brick faces flaking or peeling off (spalling)Soft brick, trapped moisture or a mortar that is too hardFind the moisture source and have a mason assess it
Stepped or diagonal crackPossible movement in the wall or foundationMonitor, and request a professional evaluation
Horizontal crack along a jointOften less seriousRecord and watch
Rust stains or flaking at lintels or shelf anglesCorroding steel that swells and pushes the brickPrompt professional assessment
Bulging or leaning wall sectionOut-of-plane movementKeep people away and call a professional right away
Damp patches, moss, peeling paintWater getting in or not drying outTrace the source: gutters, flashing, joints

Cracks

Not every crack is an emergency. The Virginia Department of Housing and Community Development's design guide says horizontal cracks are generally not serious, while vertical and diagonal cracks can be serious and need further inspection by professionals.

The Brick Industry Association gives firmer thresholds. Its list of structural warning signs includes cracks wider than 0.075 in. (2 mm), cracks running through multiple bricks, stepped or diagonal cracks, widespread spalling, rust at lintels or shelf angles, out-of-plane movement, and sills or water tables with no slope. The same note says structural issues call for an investigation by a professional engineer to find the cause and recommend the repair.

Seasonal movement also matters. The NPS explains that above-ground brick walls expand in warm weather, especially on south and west faces, and contract in cool weather. Cracks from this movement are normally cyclical, widening in cold weather and narrowing in heat. That is why dated photos taken in different seasons are so useful: they show whether a crack is moving with the weather or growing. For a broader explanation of how hairline openings admit water, see this article on small cracks letting water in.

Spalling and moisture

The state design guide separates two cases. If unpainted brick is spalling, it may be soft brick that needs replacing. If painted brick is spalling, water has been trapped behind the paint and has gone through freeze and thaw cycles. Damp walls, moss and peeling paint should all lead you to the source of the water.

Paint peeling from a spalled brick face

Richmond's mix of humid summers and winter freeze-thaw swings is hard on brick that is already holding water. A downspout that dumps against a wall can do more damage over a few winters than decades of normal weather.

Why the mortar deserves the closest look

In a historic brick wall, the mortar is meant to be the sacrificial part. It is softer than the brick, so it takes the wear and moisture movement, and it is repointed when it wears. That is how Richmond's 19th and early 20th century brick has lasted so long.

The mortar in those walls is lime-based. Lime mortar is made from lime and sand, and it stays softer and more permeable than modern cement mortars. It lets moisture move out through the joints and flexes slightly as the wall moves. The NPS says repointing mortar should be similar in color and composition to the original, and that older mortar was high in lime, with portland cement used only sparingly.

The problem arises when a hard, cement-heavy mortar goes into soft old brick. The NPS warns that hard mortars with high portland cement content are less permeable than the surrounding brick, which can cause further deterioration. A Virginia masonry restoration presentation for architects explains the mechanism: traditional lime mortar acts like a cushion, while cement-based mortar blocks evaporation and forces the brick face to absorb all the expansion and contraction, so the faces crumble over time.

So during your inspection, ask two questions about the joints: are they worn, and do they look like they belong? Pale gray, very hard joints that are sharper than the brick around them, with brick faces eroding beside them, are a warning sign of a past repair in the wrong mortar.

Why the mortar deserves the closest look

What the mix is made of

A lime mortar for historic brick is not one fixed recipe. The right mix depends on the age of the wall, the hardness of the brick, the sand in the original joints and the exposure of that elevation. The Virginia design guide says not to repoint with mortar stronger than the original mortar and brick, and notes that where a little Portland cement is added to the lime, it should be no more than 20 percent of the mix. Matching color and texture comes from the sand as much as the lime. We cover this in more detail in our guides to historic mortar analysis and matching mortar to brick.

Inspecting historic brick in Richmond, Virginia

Richmond has some of the oldest brick housing in Virginia, from rowhouses in the Fan and Museum District to Monument Avenue and Jackson Ward. These buildings need a few extra considerations.

  • Routine maintenance does not need a COA. The City of Richmond's Commission of Architectural Review guide states that routine maintenance does not require a Certificate of Appropriateness, that unpainted masonry may not be painted, and that the COA process usually takes 30 to 60 days. If a repair changes how the wall looks, check with the city before work begins.
  • Do not sandblast. The NPS says brick should never be sandblasted, because it destroys the exterior surface of the brick and can make it absorb water. Dark coloring on old brick is often an age-related chemical change, not dirt.
  • Be careful with sealers. The same publication says silicone treatments should be avoided on historic brick because they can damage the surface and rarely help keep water out of the wall. The state design guide also lists coatings that do not let moisture breathe out of the masonry as inappropriate.
  • Know which walls carry load. Before a detailed inspection, the NPS suggests determining which walls are loadbearing by looking at beams and joists in the basement, crawl space or attic. Our guide on crawl space brick piers explains what to check below the floor.

If you own a building in the Fan, the Museum District or along Monument Avenue, our page on historic brick repair in the Fan and Museum District describes the work we do there.

How often to inspect

The Brick Industry Association says periodic inspections can be monthly, yearly, every other year or on whatever schedule suits the building. It also recommends seasonal inspection periods so you can see how the materials behave in different weather.

A practical Richmond schedule:

  • Spring: after winter freeze-thaw, look for new spalling, loose joints and cracks that opened in the cold.
  • Late summer or fall: before the cold returns, check flashing, gutters and any open joints. This is also when cracks are at their narrowest, which gives you a baseline.
  • After severe weather: after heavy rain, hurricane remnants or high winds, check walls, chimneys and parapets.

For owners of several properties, the same discipline applies at a larger scale. A property inspection schedule with templates can help you fit a facade walk into the routine rounds.

Some cities, including New York and San Francisco, require formal facade inspections of larger buildings, often every five years and supervised by a licensed architect or engineer. Academic guidance notes that documents for the municipality where the building sits must be reviewed for compliance. Those ordinances are specific to those cities and do not apply to a Richmond house by default, but a five-year hands-on check is still a sound habit for a commercial building.

What to do with what you find

The NPS puts repairs in order: structural repairs come before minor or cosmetic ones. Active cracks should be sealed with a flexible sealant, and inactive ones may be pointed. Repointing is often needed but is best done by professionals familiar with historic masonry.

A good repair follows a few rules:

  1. Fix the water first. Repair gutters, flashing and grading before the wall, or the new work will fail the same way.
  2. Repoint only what has failed. The state design guide says to remove deteriorated mortar by hand-raking, to a depth of about one inch, and to leave sound mortar alone. Grinders and electric saws are on its list of inappropriate methods because they damage brick edges.
  3. Match the mortar. Color, hardness and permeability should all match the original.
  4. Replace only what cannot be saved. Where brick has to be replaced, match its size, color and texture. Our overview of historic brick restoration and masonry restoration methods in Richmond covers how we approach this.

If your inspection turns up bowing, a leaning wall, a widening stepped crack or heavily rusted lintels, keep people away from that area and arrange for an engineer or an experienced masonry contractor to evaluate it. Our guide on when to repoint brick sorts joint conditions by urgency.

When you are working around an older building, protecting original materials is a good principle to apply to the brick as much as to the woodwork.

Our perspective

We have spent more than 25 years repairing brick in Richmond, and nearly every failed repair we are called to fix has the same history: nobody looked closely until water had already been getting in for years.

An inspection does not need to be complicated. Walk the walls, photograph them, and look at the joints. If the mortar is soft, sandy or missing, that is the wall asking for attention. Repointing in lime mortar that matches the original is the traditional repair and, in our experience, the one that lets old brick last.

We match the existing brick and mortar on every job, and we use the methods this brick was built with. Our work carries a 5-year guarantee on materials and workmanship, we ask for no deposit, and payment is due when the work is complete. Our aim is a repair that blends in and lasts for decades.

Thomas

Have us look at your brick

If your inspection found worn joints, spalled brick, cracks or water stains, we can assess the wall and tell you what it needs. Heritage Masonry & Brick is a family-run masonry company in Richmond, VA. We handle brick repair, lime mortar repointing and tuckpointing, structural brick and masonry repairs and chimney repairs for homes and businesses.

Heritage Masonry & Brick

Estimates are free and the work is guaranteed. Call 804-324-6304 today, or visit our main site to request a visit. You can also read more on our masonry advice page.

FAQ

How often should I have a brick facade inspected?

Check at least once a year, and more often if you can: the Brick Industry Association recommends seasonal inspections. Also look after any major storm. In Richmond, spring is a good time to catch freeze-thaw damage, and early fall is good for preparing the wall for winter.

Which cracks in brick are serious?

Stepped or diagonal cracks, cracks through several bricks, and cracks wider than about 2 mm (0.075 in.) call for professional evaluation. Horizontal cracks along mortar joints are generally less serious. Photographing a crack each season shows whether it is moving.

Do I need city approval to repair brick in a Richmond historic district?

Routine maintenance does not require a Certificate of Appropriateness, according to the City of Richmond's Commission of Architectural Review. Changes to a building's appearance may, and approval usually takes 30 to 60 days. Confirm with the city before starting work that changes the look of the wall.

Why use lime mortar to repoint old brick?

Lime mortar is softer and more permeable than cement mortar, so it lets moisture escape through the joints and moves with the wall. Cement-heavy mortar can trap water in the brick and speed up its decay. For historic Richmond brick, lime mortar matched to the original is the sound choice.

Heritage Masonry & Brick
Discuss Your Brick Facade
Share what you found during your inspection and ask about brick, mortar or structural repairs for your Richmond property.

Sources